Well, the board is either fixed, or it's going to run terribly. Cross your fingers and hope for the best. I'm at my technical limit right now.

Clay Plug In Minnie Balls

Post Reply
Message
Author
SWIHARTMARK
Member
Member
Posts: 138
Joined: Mon Jun 05, 2017 5:09 pm
Age: 54
Location: DAYTON, OHIO
United States of America

Clay Plug In Minnie Balls

#1 Post by SWIHARTMARK » Tue May 15, 2018 9:20 pm

I have read where the British put a clay or wooden plug in the hollow cavity in the back of Minnie balls. I was thinking of using some air hardening clay in the cavity of my ,575 Minnie balls cast from the Lee original mold. I have a three band Snider I would like to use them in and it seems most people just go with a .585 or larger Minnie ball or use .600 round balls in a plastic 24GA shotgun hull. I think this might actually work as well or better since it was done historically. I would guess the British did some testing on this as well.

Any input would be appreciated.

Best Regards,

Mark

User avatar
Rapidrob
Global Moderator
Global Moderator
Posts: 457
Joined: Sat Jun 03, 2017 9:10 am
Age: 66
Location: New Mexico
United States of America

Re: Clay Plug In Minnie Balls

#2 Post by Rapidrob » Wed May 16, 2018 9:12 am

I would make a plug and let it harden. Then smack it with a hammer to see how hard it really is. The plug should be hard to shatter with a light blow.
The plug must leave the cavity after the bullet is free of the muzzle and has done its job of obdurating the bullet into the rifling. For accuracy each plug needs to weigh the same.
Decades ago I tried what your doing and I used a " hydraulic cement " for patching a rain water leaking basement and it worked well when cured. The cement expanded into the bullets cavity and was a tight fit when set. The plugs were found about 40 yards from the rifle when fired and were mostly intact. In combat the little plugs would be deadly as well at close range.
I cannot say that the bullets were any more accurate than non-plugged bullets but I think that was due to our poor black powder quality today. For this reason I got out of black powder firearms.
Tin Can Sailor
'Nam Vet
NRA Endowment Member
President New Mexico Military Surplus Rifle Pistol Shooters

SWIHARTMARK
Member
Member
Posts: 138
Joined: Mon Jun 05, 2017 5:09 pm
Age: 54
Location: DAYTON, OHIO
United States of America

Re: Clay Plug In Minnie Balls

#3 Post by SWIHARTMARK » Wed May 16, 2018 5:21 pm

Well, this is Crayola Air-Dry Clay, only the best for my Minnie balls. I'll still do it just to fill the air gap if nothing else. I hear it is used to make hand print molds of little kids as its main function in life. I'm guessing this stuff shatters if I look at it wrong. I did not waste any more money on any high end clay. I'm guessing the clay falls out of the cavity more ofter than not once it dries. I'll just put a bit of the wet stuff inside to make it stick as a back up plan.

Got any more information of today's bad quality black powder. I've never heard that before, but don't doubt it.

As for accuracy, I don't think I'm in your league by a country mile, but I want to hit the berm properly. If I manage to whack clay pigeons at 50 yards every once in a while, that would be fine. I'm not holding my breath though.

Thanks for your input.

Best Regards,

Mark

User avatar
Smokey
Member
Member
Posts: 134
Joined: Tue Jun 06, 2017 6:46 pm
Age: 65
Location: democrat hell of Connecticut, USA
United States of America

Re: Clay Plug In Minnie Balls

#4 Post by Smokey » Sat May 19, 2018 5:23 pm

The British Pritchett bullet used a tapered wooden plug in the base to spread the cavity skirts when it was driven into the bullet by pressure. American Minie bullets relied on the pressure in the hollow base to do the job. In trials in 1855, a rifle-musket kept all the shots in a 5-inch circle at 200 yards, and penetrated 11 one-inch pine boards.
Arguing with someone who denounces reason is like administering medicine to a corpse.

Post Reply

Return to “Antique Cartridge and Black Powder Rifles”

Who is online

Users browsing this forum: No registered users and 0 guests