Well, the board is either fixed, or it's going to run terribly. Cross your fingers and hope for the best. I'm at my technical limit right now.

Photographing a bore

Post Reply
Message
Author
User avatar
nrobertb
Bullet Banger
Bullet Banger
Posts: 661
Joined: Sat Jun 03, 2017 11:02 am
Location: NW Lower MI
United States of America

Photographing a bore

#1 Post by nrobertb » Sat Dec 02, 2017 11:13 pm

What is the best method for photographing a bore? I tried recently using a bore light and the light was washing out all of the detail. My eye could see it but the camera couldn't.

User avatar
Popeye
Senior Moderator
Senior Moderator
Posts: 136
Joined: Fri Jun 02, 2017 7:00 pm
Age: 71
Location: Sacramento area, California
United States of America

Re: Photographing a bore

#2 Post by Popeye » Tue Feb 06, 2018 2:20 am

Shine the light against the bolt face.
The difference between a Communist and a Socialist is; the Socialist doesn't have all the guns yet

User avatar
dmg4
Junior Member
Junior Member
Posts: 45
Joined: Sat Jun 10, 2017 12:48 am
Age: 63
Location: Geneva, NY
United States of America

Re: Photographing a bore

#3 Post by dmg4 » Tue Feb 06, 2018 6:33 am

What brand and model of camera are you using? There are probably some settings that would make success more likely. If you are shooting directly into the light, then it's a bit like pointing the camera into the sun and trying to capture an image. If it's a point-and-shoot, try setting it to "macro" ( the flower icon on some camera), and shooting slightly off center to the bore rather than directly down the center.

The best results would be obtained with a borescope. There are some very inexpensive USB cameras available now that couple to a smart phone or laptop.
Frequently wrong, never in doubt.

User avatar
Rapidrob
Global Moderator
Global Moderator
Posts: 532
Joined: Sat Jun 03, 2017 9:10 am
Age: 66
Location: New Mexico
United States of America

Re: Photographing a bore

#4 Post by Rapidrob » Tue Feb 06, 2018 9:57 am

Defuse the light with a piece of toilet paper on the lamp.
Tin Can Sailor
'Nam Vet
NRA Endowment Member
President New Mexico Military Surplus Rifle Pistol Shooters

72 usmc
Gun Nut
Gun Nut
Posts: 871
Joined: Fri Jun 02, 2017 10:28 pm
Age: 67
Location: Menomonee Falls, Wi
United States of America

Re: Photographing a bore

#5 Post by 72 usmc » Tue Feb 06, 2018 10:01 am

I use the tiny mag light flash light near the chamber sitting on the magazine follower so the maglight which has an adjustable beam like all mag lights is allowed to shine up the barrel. The mini mag light is about the size of a cartridge for a rifle. it can set on the mag follower and move up close or way back. In addition, you can set it wide or narrow beam and can also use a strong or weak battery to alter the light's power. For gun shows as a bore light, you always want a fresh battery. Then I use a small Cannon power shot camera on digital, macro set on spot or center weight setting. That will capture the bore 's first 3 inches so you can see the muzzle and some of the rifling or you can get chamber shots.
The flashlight is called the Maglite Solitaire LED 1-Cell AAA Flashlight Black

You can also use it at gun shows for a bore light due to its adjustable beam.
examples:
IMG_3848.JPG
IMG_3848.JPG (20.94 KiB) Viewed 1281 times
IMG_5324.JPG
IMG_3855.JPG
IMG_3855.JPG (16.05 KiB) Viewed 1281 times
IMG_3526.jpg
Last edited by 72 usmc on Thu Feb 22, 2018 8:15 pm, edited 8 times in total.
To old to fight and to old to run, a Jar head will just shoot and be done with you.

User avatar
nrobertb
Bullet Banger
Bullet Banger
Posts: 661
Joined: Sat Jun 03, 2017 11:02 am
Location: NW Lower MI
United States of America

Re: Photographing a bore

#6 Post by nrobertb » Tue Feb 06, 2018 10:08 am

Thanks for the suggestions. I'll give them a try. I'm using a Sony camera.

72 usmc
Gun Nut
Gun Nut
Posts: 871
Joined: Fri Jun 02, 2017 10:28 pm
Age: 67
Location: Menomonee Falls, Wi
United States of America

Re: Photographing a bore

#7 Post by 72 usmc » Tue Feb 06, 2018 10:31 am

one more example of a mauser bore The above are a poor bore sewer pipe and a new bore and chamber edge. Below is the mauser. Holding the camera close or at an angle or an inch or so will capture the inside more or the outside edge more. Also play with the evaluative sense setting point /spot, center, overall evaluative. Those small cameras have lots of settings for light type also. That can help some pics just get better if you switch from day light to cloudy or tungsten or florescent. have the flash off.
IMG_4091.jpg
my cheep old camera is a cannon digital power shot SD 1000 from a used camera store.
this one https://www.usa.canon.com/internet/port ... hot-sd1000 It works great with a 2003 Mac to load pics
To old to fight and to old to run, a Jar head will just shoot and be done with you.

Post Reply

Return to “Firearms Photography”

Who is online

Users browsing this forum: No registered users and 0 guests