Well, the board is either fixed, or it's going to run terribly. Cross your fingers and hope for the best. I'm at my technical limit right now.

Failure to fires with Rasheed rifle

Post Reply
Message
Author
CGSteve
Junior Member
Junior Member
Posts: 28
Joined: Sat Jun 03, 2017 11:57 pm
Age: 35
Location: Tucson
United States of America

Failure to fires with Rasheed rifle

#1 Post by CGSteve » Wed Sep 12, 2018 11:17 pm

Had my Rasheed for a while, but only recently field stripped it for inspection, cleaning, and lubing for a test shoot. I read that many of these were not used in service, but I think that isn't the case for mine. It is in good condition overall, but definitely has that carried look and there is wear on the metal parts as well.

After a field stripping and lubricating it I took it out for a test fire using Yugo surplus, Wolf, Golden Tiger and some Russian "hunting" ammo in white boxes with light blue lettering. Every type of cartridge had failures to fire. I think I successfully fired three rounds total and decided not to ruin any more ammo. After waiting a while I looked at the primers and they all had decent firing pin strikes to them. All of this is new made ammo or well stored surplus that fires every time in my AKs and SKS rifles.

Taking the rifle apart again, I see the pin floats freely and doesn't look abnormal or worn to me. What could be causing this? A weak trigger spring? The one thing I notice though is while manually working the action, the resistance seems slow and sluggish when pulling the handle to the rear and releasing it. A weak recoil spring perhaps but this should not affect firing.

I know these rifles and parts are uncommon so replacing anything will be a challenge but I just want to hear thoughts from those more knowledgeable than me.

milsurphunter
Registered User
Registered User
Posts: 1
Joined: Sun Jun 04, 2017 4:39 am
Location: Frederick, MD
United States of America

Re: Failure to fires with Rasheed rifle

#2 Post by milsurphunter » Thu Sep 13, 2018 4:29 am

Hi First time posting, and I don't know if this is going to help.
I had similar experience with my Rasheed, sometimes the bolt will not return to full battery due to gas port setting, cuasing the lite strike.
Try to manually push the bolt, like the forward assit on the AR. If this is the cause, you have to adjust the gas regulator.

User avatar
Rapidrob
Global Moderator
Global Moderator
Posts: 664
Joined: Sat Jun 03, 2017 9:10 am
Age: 67
Location: New Mexico
United States of America

Re: Failure to fires with Rasheed rifle

#3 Post by Rapidrob » Thu Sep 13, 2018 12:38 pm

You say you have deep firing pin strikes. The only way the cartridge could not fire with a deep strike is a slow firing pin. I'd check for displaced Cosmoline or a weak spring.
Make sure the firing pin seat in the bolt is free and clear.
Tin Can Sailor
'Nam Vet
NRA Endowment Member
President New Mexico Military Surplus Rifle Pistol Shooters

CGSteve
Junior Member
Junior Member
Posts: 28
Joined: Sat Jun 03, 2017 11:57 pm
Age: 35
Location: Tucson
United States of America

Re: Failure to fires with Rasheed rifle

#4 Post by CGSteve » Thu Sep 13, 2018 11:08 pm

milsurphunter wrote:
Thu Sep 13, 2018 4:29 am
Hi First time posting, and I don't know if this is going to help.
I had similar experience with my Rasheed, sometimes the bolt will not return to full battery due to gas port setting, cuasing the lite strike.
Try to manually push the bolt, like the forward assit on the AR. If this is the cause, you have to adjust the gas regulator.
That's not the case as the very first round doesn't fire, so it's not the return.

Rob, I will disassemble the bolt and see but when I field stripped it, it floated nicely.

Thanks for the replies both of you.

ammolab
Member
Member
Posts: 101
Joined: Sat Jun 03, 2017 9:34 pm
Location: New Mexico USA
United States of America

Re: Failure to fires with Rasheed rifle

#5 Post by ammolab » Fri Sep 14, 2018 7:15 pm

I have seen several Hakim's and Rashids in need of a new hammer spring (same part?) for reliable ignition.

I received a lot of Century's spare parts and hammer springs sold out first.

CGSteve
Junior Member
Junior Member
Posts: 28
Joined: Sat Jun 03, 2017 11:57 pm
Age: 35
Location: Tucson
United States of America

Re: Failure to fires with Rasheed rifle

#6 Post by CGSteve » Fri Sep 14, 2018 9:28 pm

I can't positively say that's the issue but I'd give it a shot. Any connections still on parts? Thanks.

User avatar
Rapidrob
Global Moderator
Global Moderator
Posts: 664
Joined: Sat Jun 03, 2017 9:10 am
Age: 67
Location: New Mexico
United States of America

Re: Failure to fires with Rasheed rifle

#7 Post by Rapidrob » Mon Sep 17, 2018 11:12 pm

How much effort does it take to cock the hammer? Is it uncomfortable to push the hammer back and catch the sear? If not,the hammer spring is too weak.
Tin Can Sailor
'Nam Vet
NRA Endowment Member
President New Mexico Military Surplus Rifle Pistol Shooters

ammolab
Member
Member
Posts: 101
Joined: Sat Jun 03, 2017 9:34 pm
Location: New Mexico USA
United States of America

Re: Failure to fires with Rasheed rifle

#8 Post by ammolab » Wed Sep 19, 2018 11:21 am

CGSteve wrote:
Fri Sep 14, 2018 9:28 pm
I can't positively say that's the issue but I'd give it a shot. Any connections still on parts? Thanks.
There are guys selling Hakim parts on eBay. The Rashid hammer spring is different but send those sellers a message..they may have your part.

User avatar
Rapidrob
Global Moderator
Global Moderator
Posts: 664
Joined: Sat Jun 03, 2017 9:10 am
Age: 67
Location: New Mexico
United States of America

Re: Failure to fires with Rasheed rifle

#9 Post by Rapidrob » Fri Sep 21, 2018 10:08 pm

Wolff Springs Will have a spring that will fit. You may have to buy a "Gunsmith Special" of ten springs for a few bucks that will have a spring that fits.
Tin Can Sailor
'Nam Vet
NRA Endowment Member
President New Mexico Military Surplus Rifle Pistol Shooters

CGSteve
Junior Member
Junior Member
Posts: 28
Joined: Sat Jun 03, 2017 11:57 pm
Age: 35
Location: Tucson
United States of America

Re: Failure to fires with Rasheed rifle

#10 Post by CGSteve » Sun Sep 23, 2018 3:32 pm

Thanks gents.

CGSteve
Junior Member
Junior Member
Posts: 28
Joined: Sat Jun 03, 2017 11:57 pm
Age: 35
Location: Tucson
United States of America

Re: Failure to fires with Rasheed rifle

#11 Post by CGSteve » Sun Oct 14, 2018 2:54 pm

I checked with Wolff springs and they said they do not know if SKS springs will work in the Rasheed and cannot do custom orders, which is understandable as it would not be cost effective for them.

Post Reply

Return to “Middle East and North African Rifles”

Who is online

Users browsing this forum: No registered users and 3 guests