So far good! This newbie still has his fingers

Post Reply
Reverend Mauser
Member
Member
Posts: 65
Joined: Mon Jul 03, 2017 10:55 am
Age: 46
Location: Kansas, USA

So far good! This newbie still has his fingers

Post by Reverend Mauser »

I tried my hand loads for the first time yesterday afternoon and am still intact. I'm new to reloading and am using the classic Lee Loaders. I had a solid group with my 22-250 and, although my 30-06 is stringing vertically, (a preexistent issue I have to correct) the round column wasn't much more than an inch wide. A little work with the rifle is in order, but it looks promising.
User avatar
Rapidrob
Global Moderator
Global Moderator
Posts: 1108
Joined: Sat Jun 03, 2017 9:10 am
Age: 68
Location: New Mexico

Re: So far good! This newbie still has his fingers

Post by Rapidrob »

Good for you!. LEE Loaders are a solid 3/4 powder charge load. Not the fastest,but in most instances,the best in accuracy.
Vertical stringing is almost always action screws too tight,or wood touching the barrel.
That being said, some rifles like a "fouled bore". A couple of fouling shots are fired and the bullet group will shrink.
Tin Can Sailor
'Nam Vet
NRA Endowment Member
President New Mexico Military Surplus Rifle Pistol Shooters
Reverend Mauser
Member
Member
Posts: 65
Joined: Mon Jul 03, 2017 10:55 am
Age: 46
Location: Kansas, USA

Re: So far good! This newbie still has his fingers

Post by Reverend Mauser »

Vertical stringing is almost always action screws too tight,or wood touching the barrel.
It's a Savage 111 and read a while back on savageshooters that they can be particularly picky about the action screws. I

I did a free float a while back as the very front of the stock was touching, but it did not solve the issue.

I can tell even so that there was improvement. This stringing was the straightest pattern I've ever seen it do, so I'm thinking the hand loads were an improvement.
Kurt
Member
Member
Posts: 56
Joined: Fri Jul 14, 2017 3:25 pm
Age: 66
Location: Greensburg PA

Re: So far good! This newbie still has his fingers

Post by Kurt »

The bedding required on a Model 111 is illustrated on youtube somewhere and it is shown that it is important to bend the rear action screw as well as the forward receiver/barrel. If yours has the cheaply made synthetic stock, as does mine, it is a bit tricky but it can be done and is effective. Good luck with your new pursuits!
Reverend Mauser
Member
Member
Posts: 65
Joined: Mon Jul 03, 2017 10:55 am
Age: 46
Location: Kansas, USA

Re: So far good! This newbie still has his fingers

Post by Reverend Mauser »

Kurt wrote: Wed Jun 27, 2018 1:10 am The bedding required on a Model 111 is illustrated on youtube somewhere and it is shown that it is important to bend the rear action screw as well as the forward receiver/barrel. If yours has the cheaply made synthetic stock, as does mine, it is a bit tricky but it can be done and is effective. Good luck with your new pursuits!
This is good to know. This is a wood stock. A lot of savage people also say it's important to float the tang on the 110, and it looks like some work needs to be done there.

I got a torque screwdriver the other day, so the action screws are going to be tightened appropriately. I've had issues with mine loosening up, and that certainly needs attention, even if it is not a full cure.
User avatar
Tommy Atkins
Global Moderator
Global Moderator
Posts: 963
Joined: Sat Jun 03, 2017 4:47 pm
Age: 66
Location: Hagerstown, MD

Re: So far good! This newbie still has his fingers

Post by Tommy Atkins »

There's nothings wrong with the good old Lee "Whack-a-Mole"!
I taught a total newbie to load .303 British with one on a picnic bench in the Ozarks, in an afternoon.
He too was nervous at first, but pretty soon he was whacking out rounds at the rate of 2 every 3 minutes.

(He's gonna kill me when he finds the one 215 Gr hard cast "full house" black powder load I snuk in the box though)!
:shock: :whistle:
User avatar
Smokey
Member
Member
Posts: 235
Joined: Tue Jun 06, 2017 6:46 pm
Age: 67
Location: West Virginia

Re: So far good! This newbie still has his fingers

Post by Smokey »

NASTY!! :naughty:
Hope he knows how to clean the black fouling out!!
You might need to mention the necessity for preventing corrosion.
Arguing with someone who denounces reason is like administering medicine to a corpse.
User avatar
Tommy Atkins
Global Moderator
Global Moderator
Posts: 963
Joined: Sat Jun 03, 2017 4:47 pm
Age: 66
Location: Hagerstown, MD

Re: So far good! This newbie still has his fingers

Post by Tommy Atkins »

He's a very meticulous person & he always cleans after shooting before the sun goes down. He's also shooting MkVII ball so he cleans for corrosive automatically.
(I'll remind him anyway, as I'm pretty sure he'll call me when it gets fired) :lol:
kraggman
Junior Member
Junior Member
Posts: 34
Joined: Sat Jun 17, 2017 4:51 pm
Age: 64
Location: USA New Jersey

Re: So far good! This newbie still has his fingers

Post by kraggman »

Nice. I started with Lee Loaders. Good for taking your time and getting used to the process.


Sent from my iPhone using Tapatalk
Post Reply

Return to “Reloading”