Well, the board is either fixed, or it's going to run terribly. Cross your fingers and hope for the best. I'm at my technical limit right now.

Lee Crimp Die for 6.5 Arisaka?

Post Reply
Message
Author
BigMau
Junior Member
Junior Member
Posts: 33
Joined: Sun Jun 11, 2017 7:59 am
Age: 49
Location: Lords Valley, Pennsylvania USA
United States of America

Lee Crimp Die for 6.5 Arisaka?

#1 Post by BigMau » Wed Feb 07, 2018 4:54 pm

I am reloading cast bullets for my Arisaka T38 rifle in 6.5 Arisaka cal.

Anyone use a Lee crimp die??? If so... should I get a custom made die or can I use another type of 6.5mm rifle Crimp die?? :think: :think:

User avatar
nrobertb
Bullet Banger
Bullet Banger
Posts: 706
Joined: Sat Jun 03, 2017 11:02 am
Location: NW Lower MI
United States of America

Re: Lee Crimp Die for 6.5 Arisaka?

#2 Post by nrobertb » Wed Feb 07, 2018 7:34 pm

I don't crimp mine. They work fine without it imho.

BigMau
Junior Member
Junior Member
Posts: 33
Joined: Sun Jun 11, 2017 7:59 am
Age: 49
Location: Lords Valley, Pennsylvania USA
United States of America

Re: Lee Crimp Die for 6.5 Arisaka?

#3 Post by BigMau » Wed Feb 07, 2018 8:36 pm

nrobertb wrote:
Wed Feb 07, 2018 7:34 pm
I don't crimp mine. They work fine without it imho.
I don't crimp FMJ bullets 6.5 Arisaka....

However, in 8mm Mauser and 7.62x54R... I use a Lee factory crimp die.

User avatar
nrobertb
Bullet Banger
Bullet Banger
Posts: 706
Joined: Sat Jun 03, 2017 11:02 am
Location: NW Lower MI
United States of America

Re: Lee Crimp Die for 6.5 Arisaka?

#4 Post by nrobertb » Wed Feb 07, 2018 9:09 pm

I should have mentioned that I only single load so there is no problem with recoil moving the bullets. Obviously if you are firing from a magazine it is a whole other kettle of fish.

slowbob2
Member
Member
Posts: 101
Joined: Fri Jul 21, 2017 4:02 pm
Age: 38
Location: slaton
United States of America

Re: Lee Crimp Die for 6.5 Arisaka?

#5 Post by slowbob2 » Wed Feb 07, 2018 10:11 pm

If you crimp a cast bullet it hurts the accuracy . The more you crimp it , the more it shaves the bullet as it exits the case mouth .

ammolab
Member
Member
Posts: 80
Joined: Sat Jun 03, 2017 9:34 pm
Location: New Mexico USA
United States of America

Re: Lee Crimp Die for 6.5 Arisaka?

#6 Post by ammolab » Fri Feb 09, 2018 12:37 am

slowbob2 wrote:
Wed Feb 07, 2018 10:11 pm
If you crimp a cast bullet it hurts the accuracy . The more you crimp it , the more it shaves the bullet as it exits the case mouth .
Would this then not hurt accuracy on cast revolver ammunition. Such factory ammo is heavily crimped as are my great shooting reloads.

slowbob2
Member
Member
Posts: 101
Joined: Fri Jul 21, 2017 4:02 pm
Age: 38
Location: slaton
United States of America

Re: Lee Crimp Die for 6.5 Arisaka?

#7 Post by slowbob2 » Sun Feb 11, 2018 4:42 pm

Accuracy levels are different between handguns and rifles , as are the velocity , distances ,twist rates and pressure . Plus what you are getting and thinking is great accuracy and my standards my be different . Crimping is never used in any rifle accuracy matches . It can help with the performance of poor quality handloads .

SWIHARTMARK
Member
Member
Posts: 153
Joined: Mon Jun 05, 2017 5:09 pm
Age: 54
Location: DAYTON, OHIO
United States of America

Re: Lee Crimp Die for 6.5 Arisaka?

#8 Post by SWIHARTMARK » Sun Feb 11, 2018 8:55 pm

Check the Lee Precision site and see if they have any in clearance. Sometimes they over produce for a custom order and list them for clearance. That's how I got mine. I like to factory crimp with Lee after crushing a few cases early in my reloading days. You can adjust the firmness of the crimp to adjust for accuracy, just like a roll crimp. Both can be adjusted, so I cannot fathom what the difference would be if you experiment with it.

I have found the internal diameters of many dies to be woefully undersized, so crimping might be the least of your worries. I have my own gauge pins from .060 to .500 and have access to intra-micrometers which can measure to .0001" on inside diameters with three contact points. I'm seriously thinking of making my own neck sizers to take that out of play in my reloading. I already have for 45/70 and it worked great.

Best Regards,

Mark

Post Reply

Return to “Reloading”

Who is online

Users browsing this forum: No registered users and 2 guests