Carcano Test Shoot

slowbob2
Member
Member
Posts: 199
Joined: Fri Jul 21, 2017 4:02 pm
Age: 38
Location: slaton

Re: Carcano Test Shoot

Post by slowbob2 »

Sticky bolt can be one of two things. First if dry fired a lot , the slot that the cocking piece rides in can get beat up . That will make the bolt lift much harder . IT can be sanded back smooth . On the custom rifles I build from Carcanos , the more you smooth up that surface , the slicker the bolt gets . What bullet was in the ammo you used , .264 or .268 ? The .268 bullet is made wrong and can cause pressure problems in many guns . That will also make the bolt hard to lift . What do the primers and case heads look like on fired brass ? 50 yards will not tell you much , that is so close even smooth bores shoot ok there , it takes about 70 yards for a problem to start to show . It will deviate at LEAST 3x at 100 and 6x at 200 .
CGSteve
Junior Member
Junior Member
Posts: 44
Joined: Sat Jun 03, 2017 11:57 pm
Age: 36
Location: Tucson

Re: Carcano Test Shoot

Post by CGSteve »

slowbob2 wrote: Sun Jan 14, 2018 8:50 am Sticky bolt can be one of two things. First if dry fired a lot , the slot that the cocking piece rides in can get beat up . That will make the bolt lift much harder . IT can be sanded back smooth . On the custom rifles I build from Carcanos , the more you smooth up that surface , the slicker the bolt gets . What bullet was in the ammo you used , .264 or .268 ? The .268 bullet is made wrong and can cause pressure problems in many guns . That will also make the bolt hard to lift . What do the primers and case heads look like on fired brass ? 50 yards will not tell you much , that is so close even smooth bores shoot ok there , it takes about 70 yards for a problem to start to show . It will deviate at LEAST 3x at 100 and 6x at 200 .
The bullets are .268 from Graf & Son's ammo. The previous ammo I was using was the PPU stuff with the boat tail bullets that caused feeding issues. The brass looked fine except upon close inspection there appeared to be a light scrape not too far up from the base. So is there no correctly sized factory ammo out there? The rifle did not feel "off" or unusual in any way upon firing.
slowbob2
Member
Member
Posts: 199
Joined: Fri Jul 21, 2017 4:02 pm
Age: 38
Location: slaton

Re: Carcano Test Shoot

Post by slowbob2 »

Flattened primers , loose primers , swelled case head . Any will be signs of high case pressure . As will a hard to lift bolt . Was the bolt hard to lift with the other ammo ?
VMASCIOP2000
Member
Member
Posts: 119
Joined: Fri Jun 09, 2017 12:41 am
Age: 63
Location: oakdale minnesota

Re: Carcano Test Shoot

Post by VMASCIOP2000 »

CGSteve wrote: Mon Jan 15, 2018 10:12 pm
slowbob2 wrote: Sun Jan 14, 2018 8:50 am Sticky bolt can be one of two things. First if dry fired a lot , the slot that the cocking piece rides in can get beat up . That will make the bolt lift much harder . IT can be sanded back smooth . On the custom rifles I build from Carcanos , the more you smooth up that surface , the slicker the bolt gets . What bullet was in the ammo you used , .264 or .268 ? The .268 bullet is made wrong and can cause pressure problems in many guns . That will also make the bolt hard to lift . What do the primers and case heads look like on fired brass ? 50 yards will not tell you much , that is so close even smooth bores shoot ok there , it takes about 70 yards for a problem to start to show . It will deviate at LEAST 3x at 100 and 6x at 200 .
The bullets are .268 from Graf & Son's ammo. The previous ammo I was using was the PPU stuff with the boat tail bullets that caused feeding issues. The brass looked fine except upon close inspection there appeared to be a light scrape not too far up from the base. So is there no correctly sized factory ammo out there? The rifle did not feel "off" or unusual in any way upon firing.
You may need to polish the chamber to smooth out whatever is causing that scrape.
I was R.L.E.V.M. on our old forum.
Post Reply

Return to “Italian Rifles”