Well, the board is either fixed, or it's going to run terribly. Cross your fingers and hope for the best. I'm at my technical limit right now.

M1/M14 marring other riflestocks in your gunsafe?

Post Reply
Message
Author
User avatar
Youngblood
Registered User
Registered User
Posts: 23
Joined: Sat Jun 03, 2017 8:55 pm
Age: 65
Location: Virginia, USA
United States of America

M1/M14 marring other riflestocks in your gunsafe?

#1 Post by Youngblood » Sun Jun 04, 2017 3:35 pm

M1/M14 Variant marring other riflestocks in your gunsafe?

Image

:)
First licensed to carry concealed in 1975.

fordmech00
Junior Member
Junior Member
Posts: 31
Joined: Sat Jun 03, 2017 4:35 pm
Location: Pennsylvania
United States of America

Re: M1/M14 marring other riflestocks in your gunsafe?

#2 Post by fordmech00 » Sun Jun 04, 2017 6:52 pm

You sir are a genius 😀

User avatar
Youngblood
Registered User
Registered User
Posts: 23
Joined: Sat Jun 03, 2017 8:55 pm
Age: 65
Location: Virginia, USA
United States of America

Re: M1/M14 marring other riflestocks in your gunsafe?

#3 Post by Youngblood » Sun Jun 04, 2017 7:08 pm

:) Thanks.

BTW, those items are cut from thick vinyl tubing that can be purchased by the foot at Lowes (and probably other places).

1"OD x 3/4"ID & 1/2"OD x 3/8"ID

Enjoy!
First licensed to carry concealed in 1975.

DeaconKC
Senior Moderator
Senior Moderator
Posts: 67
Joined: Fri Jun 02, 2017 10:57 pm
Location: Southern Illinois
United States of America

Re: M1/M14 marring other riflestocks in your gunsafe?

#4 Post by DeaconKC » Sun Jun 04, 2017 7:25 pm

That is a great idea
"Let courage rise with danger, and strength to strength oppose."

DaleH
Junior Member
Junior Member
Posts: 43
Joined: Sun Jun 04, 2017 9:24 pm
Age: 57
Location: Mass, USA
United States of America

Re: M1/M14 marring other riflestocks in your gunsafe?

#5 Post by DaleH » Mon Jun 05, 2017 12:02 pm

I have a plastic sight protector that slip over the rear & front sights (M1) and have been placing a yellow "thread protector" rubber cap on the op handle. Any hardware store carries them. Some places sell them as 'vacuum caps' to protect oil/gas line fitting ends.

User avatar
jones0430
Member
Member
Posts: 68
Joined: Sat Jun 03, 2017 10:14 pm
Age: 68
Location: Dallas
United States of America

Re: M1/M14 marring other riflestocks in your gunsafe?

#6 Post by jones0430 » Tue Jun 06, 2017 1:20 am

I just use a rifle sock.

timbo1955
Registered User
Registered User
Posts: 7
Joined: Tue Jun 13, 2017 4:17 pm
Age: 71
Location: pumpkin center, CA
Ireland

Re: M1/M14 marring other riflestocks in your gunsafe?

#7 Post by timbo1955 » Tue Jun 20, 2017 10:48 am

been using automotive vacuum caps on the M1 and M1A , FN49"s , of course after I scratched and dented the works

bobvz
Junior Member
Junior Member
Posts: 35
Joined: Mon Jun 05, 2017 8:50 pm
Location: USA, SC
United States of America

Re: M1/M14 marring other riflestocks in your gunsafe?

#8 Post by bobvz » Fri Jun 30, 2017 8:25 pm

I alternate my rifles muzzle up muzzle down. This prevents mishaps like that. It also allows you to get more guns in your safe.

Post Reply

Return to “US Rifles”

Who is online

Users browsing this forum: No registered users and 1 guest