Well, the board is either fixed, or it's going to run terribly. Cross your fingers and hope for the best. I'm at my technical limit right now.

Search found 286 matches

by KneverKnew
Sun Apr 12, 2020 1:43 pm
Forum: General Ammunition
Topic: 8mm Spam Can Identification. Please HELP.
Replies: 8
Views: 466
United States of America

Re: 8mm Spam Can Identification. Please HELP.

Thanks. From the can label I believe there are no stripper clips. It says 480 instead of 440 and says FARA LAME which I believe means no strippers.
by KneverKnew
Sun Apr 12, 2020 12:38 pm
Forum: General Ammunition
Topic: 8mm Spam Can Identification. Please HELP.
Replies: 8
Views: 466
United States of America

Re: 8mm Spam Can Identification. Please HELP.

I appreciate the info on van markings but none show the same markings on my can.
by KneverKnew
Sun Apr 12, 2020 12:11 pm
Forum: General Ammunition
Topic: 8mm Spam Can Identification. Please HELP.
Replies: 8
Views: 466
United States of America

8mm Spam Can Identification. Please HELP.

I have this unopened can of 380 rounds of 8mm Ammo.
Can anyone tell me
What kind this is?
EEF53A41-9B5C-42DD-82B1-50F820172709.jpeg
by KneverKnew
Thu Mar 19, 2020 7:19 pm
Forum: Swiss Rifles
Topic: Peabody Model 1867 Swiss Contract Rifle
Replies: 0
Views: 1686
United States of America

Peabody Model 1867 Swiss Contract Rifle

Anybody know anything about these rifles and their history? Are they very scarce? What would one be worth if I came Across one?
by KneverKnew
Mon Mar 09, 2020 6:03 pm
Forum: Bullet Casting
Topic: Casting .453” soft lead bullets for cut down, worn vetterli
Replies: 2
Views: 3454
United States of America

Re: Casting .453” soft lead bullets for cut down, worn vetterli

Well...never mind then. I went ahead and loaded some up and shot them. Nice mild load of 8.5grains Unique under a 230 grain truncated comes cast Bullet. Average V of five shots was 1067 FPS. At 40 yards I got a 2” group. And this was just my first try. Going to cast more with softer lead and load di...
by KneverKnew
Mon Mar 09, 2020 12:16 pm
Forum: Bullet Casting
Topic: Casting .453” soft lead bullets for cut down, worn vetterli
Replies: 2
Views: 3454
United States of America

Casting .453” soft lead bullets for cut down, worn vetterli

So my cut down Swiss vetterli with pitted throat and first 1/3 of bore run slugs .447” groove diameter and .427” at the lands. I used a .453” 45 acp lead Bullet to slug with. I have a good supply of bought cast alloy 45 acp bullets around 200-240 grains. I also have a 230 grain round nose 45 acp Lee...
by KneverKnew
Sun Mar 08, 2020 2:18 pm
Forum: FN FAL/L1A1/STG58
Topic: My first FN-49!
Replies: 20
Views: 7272
United States of America

Re: My first FN-49!

My guess is they had to do it to get by which ever state regulations they were dealing with. That’s only a guess though. Here’s a close-up of the muzzle. 396497D1-86FB-46D7-90C1-C06B0981A022.jpeg The Only other Noticeable Issue I would like to address is that the left rear sight dog ear is slightly ...
by KneverKnew
Wed Mar 04, 2020 2:16 pm
Forum: FN FAL/L1A1/STG58
Topic: My first FN-49!
Replies: 20
Views: 7272
United States of America

Re: My first FN-49!

I did just recently purchased 200 rounds of PRVI’s 200 grain Match Ammo. We will see how that performs.
by KneverKnew
Wed Mar 04, 2020 2:14 pm
Forum: FN FAL/L1A1/STG58
Topic: My first FN-49!
Replies: 20
Views: 7272
United States of America

Re: My first FN-49!

I think that might be certain Turk surplus. Not sure. Why I’m asking.
by KneverKnew
Wed Mar 04, 2020 9:14 am
Forum: FN FAL/L1A1/STG58
Topic: My first FN-49!
Replies: 20
Views: 7272
United States of America

Re: My first FN-49!

Any suggestions on which milsurp Ammo is best (safe) to use in the FN?
by KneverKnew
Wed Mar 04, 2020 9:13 am
Forum: FN FAL/L1A1/STG58
Topic: My first FN-49!
Replies: 20
Views: 7272
United States of America

Re: My first FN-49!

Rifle arrives tomorrow. Being an Egyptian Century Import FN, what’s the chance it already has a safe two piece firing pin?
If I need to order a two piece, which do I get?
I’ve seen both with and without safety notch. ??????
by KneverKnew
Sat Feb 29, 2020 8:58 pm
Forum: FN FAL/L1A1/STG58
Topic: My first FN-49!
Replies: 20
Views: 7272
United States of America

Re: My first FN-49!

I have access to a barrel. What does it take to swap them out?
by KneverKnew
Sat Feb 29, 2020 8:47 am
Forum: FN FAL/L1A1/STG58
Topic: My first FN-49!
Replies: 20
Views: 7272
United States of America

Re: My first FN-49!

Yes thanks. I was looking at those. Now, how can I attach to muzzle other than just welding in place? I’d love to restore the battle as much as possible so that the nose cap can be removed if needed. I’m open to all options though.
by KneverKnew
Fri Feb 28, 2020 9:38 pm
Forum: FN FAL/L1A1/STG58
Topic: My first FN-49!
Replies: 20
Views: 7272
United States of America

Re: My first FN-49!

Pictures didn’t show crest. Just have to wait for delivery. Doubtful it all matches. It’s a Century after all. LOL.
by KneverKnew
Fri Feb 28, 2020 8:22 am
Forum: FN FAL/L1A1/STG58
Topic: My first FN-49!
Replies: 20
Views: 7272
United States of America

Re: My first FN-49!

Thanks Bob for those suggestions. I don’t have the rifle yet so won’t know the bore condition until then. I do have a friend who has a complete 8mm barrel assembly if necessary.

Go to advanced search