Well, the board is either fixed, or it's going to run terribly. Cross your fingers and hope for the best. I'm at my technical limit right now.

Search found 18 matches

by Tuna
Wed May 16, 2018 4:10 pm
Forum: M1 Carbine
Topic: Low serial numbers, do they add value?
Replies: 8
Views: 493
United States of America

Re: Low serial numbers, do they add value?

If a low serial number carbine has not been rebuilt then yes the low number will add value to it. But if it has been rebuilt then the value is the same as any other rebuilt carbine.
by Tuna
Tue Apr 03, 2018 1:49 pm
Forum: French Pistols
Topic: 1935A
Replies: 12
Views: 1187
United States of America

Re: 1935A

Thank you for the information. This is what I needed to know.
by Tuna
Tue Apr 03, 2018 1:42 pm
Forum: French Rifles
Topic: Double headed screw
Replies: 2
Views: 400
United States of America

Re: Double headed screw

72USMC, Your right it is on the wrong forum my bad. But I did order what I needed and I think you very much.
by Tuna
Mon Apr 02, 2018 8:14 pm
Forum: French Rifles
Topic: Double headed screw
Replies: 2
Views: 400
United States of America

Double headed screw

Can anyone ID a double headed screw that is through the stock of most Lebel and Berthier rifles. It sits above the rear of the trigger guard. And would anyone know where I may find one? Thanks.
by Tuna
Sun Apr 01, 2018 7:39 pm
Forum: Reloading
Topic: Powder in 1942 30-06?
Replies: 7
Views: 768
United States of America

Re: Powder in 1942 30-06?

Dupont IMR 4895 was the powder used by the US military to load all 30-06 M2 and M1 ammunition during WW2. When the war ended there were so many hundreds of tons of IMR 4895 around and the government sold it as surplus at pennies on the dollar. Hodgdon started buying a little at a time of this powder...
by Tuna
Sun Apr 01, 2018 7:16 pm
Forum: French Pistols
Topic: 1935A
Replies: 12
Views: 1187
United States of America

Re: 1935A

Mark I have used Wolff springs for just about all my firearms pistol, revolver and rifles that need spring replacement. I ordered one for the A and one for the S but found that the guide just does not come apart readily.
by Tuna
Sun Apr 01, 2018 4:19 pm
Forum: French Pistols
Topic: 1935A
Replies: 12
Views: 1187
United States of America

Re: 1935A

One thing that is a bit puzzling is how to remove the recoil spring from the guide rod. It is not able to slid off the guide and I would like to replace it with a new one. IT looks like there is a pin on ne end. Is this drifted out to then remove the spring? As to the rifling in the barrel. I don't ...
by Tuna
Sun Apr 01, 2018 4:16 pm
Forum: French Pistols
Topic: 1935A
Replies: 12
Views: 1187
United States of America

Re: 1935A

One thing that is a bit puzzling is how to remove the recoil spring from the guide rod. It is not able to slid off the guide and I would like to replace it with a new one. IT looks like there is a pin on ne end. Is this drifted out to then remove the spring? As to the rifling in the barrel. I don't ...
by Tuna
Sun Mar 25, 2018 2:38 pm
Forum: French Pistols
Topic: 1935A
Replies: 12
Views: 1187
United States of America

Re: 1935A

I only use my cut down brass or some Bertrum in 7.65 that I bought years ago. I had to use .32 acp dies which did not work very well at all. So I just stopped reloading for the 7.65. I recently was able to get in on a multiple purchase of Lee custom made dies in 7.65 long. Now I use these to load al...
by Tuna
Thu Mar 22, 2018 9:55 pm
Forum: French Pistols
Topic: 1935A
Replies: 12
Views: 1187
United States of America

Re: 1935A

Oh yes I have seen those posts. I am not new to the 7.65 Long cartridge and have dies for it. The worst part is the exterior finish and I am thinking of having it reblued. I do have a 1935 S that I shoot and enjoy. The slide does seem to be a bit on the loose side and not like my 1935 S. Almost like...
by Tuna
Thu Mar 22, 2018 8:03 pm
Forum: French Pistols
Topic: 1935A
Replies: 12
Views: 1187
United States of America

1935A

Gentleman. I just picked up a 1935 A with a worn finish. The last owner felt it was a wall hanger but when I took it apart I found it to be quite the opposite. Internally in good shape with nice shiny bore. The rails have finish wear as does the rest of the exterior of the pistol., What would be a b...
by Tuna
Wed Aug 30, 2017 8:09 pm
Forum: General Ammunition
Topic: How desirable is 9mm largo?
Replies: 12
Views: 4467
United States of America

Re: How desirable is 9mm largo?

While there is a demand for this ammo it is not a huge one and is limited. More people have a pistol but never shoot it and it just sits in a safe. They may have a box of ammo that also just sits there. Not a big demand cartridge. You can use .38 auto or .38 Super brass to make the rounds as Rapidro...
by Tuna
Wed Aug 30, 2017 7:42 pm
Forum: M1 Carbine
Topic: M1 Carbine Re-Patriation
Replies: 9
Views: 3182
United States of America

Re: M1 Carbine Re-Patriation

From what I was told, Century is just waiting for the OK from the State Dept. to bring them back to the US. They have already been paid for and it was our last Pres, who to please his anti-gun people blocked the importing of them. This after the State Dept. had at first approved them for import. The...
by Tuna
Tue Aug 29, 2017 10:49 pm
Forum: General Ammunition
Topic: Korean .30-06 Ammo Warning
Replies: 3
Views: 1332
United States of America

Re: Korean .30-06 Ammo Warning

The PS head stamped ammo is not corrosive primed. Now those marked KA are corrosive primed.
by Tuna
Tue Aug 29, 2017 10:40 pm
Forum: M1 Carbine
Topic: M1 Carbine Re-Patriation
Replies: 9
Views: 3182
United States of America

Re: M1 Carbine Re-Patriation

According to the South Korean government, they own them. In fact they sold them to a group headed by Century but they were prevented by our former Pres and the Hilda Beast from bringing them into the country.

Go to advanced search