Well, the board is either fixed, or it's going to run terribly. Cross your fingers and hope for the best. I'm at my technical limit right now.

Search found 251 matches

by Tommy Atkins
Sun May 20, 2018 9:20 am
Forum: Bayonets, Knives and Swords
Topic: Pat '07 Bayonet for my SMLE
Replies: 6
Views: 175
Canada

Re: Pat '07 Bayonet for my SMLE

If only the seller would actually mail it it would be nice. Estimated delivery was 15th to 22 nd!
:violin: :naughty:
He's claiming health issues & promising to ship "Any day now, any day now"!
by Tommy Atkins
Sun May 20, 2018 9:16 am
Forum: British Empire and Commonwealth
Topic: Who has a stacking swivel for a No. 4 Mk1
Replies: 6
Views: 142
Canada

Re: Who has a staclomg seovel for a No. 4 Mk1

Yes that's (only) for a No1. The screw thread is different & so is the offset for the old volley sights.
IIRC you'll have a hard time getting one for the No4, because they were discontinued during the No1 era. The only ones I can think of are the old Turkish stacking rods.
by Tommy Atkins
Thu May 17, 2018 9:06 am
Forum: Reloading
Topic: Advice on annealing--and YouTube posts to evaluate
Replies: 18
Views: 288
Canada

Re: Advice on annealing--and YouTube posts to evaluate

Actually melting the case is a bit over the top.
It used to be you'd heat to cherry red, that excessive! Now there are ways to actually measure the real temp which is way better.
by Tommy Atkins
Wed May 16, 2018 11:16 am
Forum: Reloading
Topic: Advice on annealing--and YouTube posts to evaluate
Replies: 18
Views: 288
Canada

Re: Advice on annealing--and YouTube posts to evaluate

Sorry but its not me that has it reversed: "The temperature range for process annealing ranges from 260 °C (500 °F) to 760 °C (1400 °F), depending on the alloy in question." "In the cases of copper, steel, silver, and brass, this process is performed by heating the material (generally until glowing)...
by Tommy Atkins
Tue May 15, 2018 6:12 pm
Forum: Reloading
Topic: Advice on annealing--and YouTube posts to evaluate
Replies: 18
Views: 288
Canada

Re: Advice on annealing--and YouTube posts to evaluate

OK wrap up: 1: "red hot" is too hot. 2: If the brass changes color like these, its annealed. (In my setup usually 5~8 seconds depending on circumstances, which is why you need the templi-sticks), which you can get from your local welding supply place. 3: you do not need water to quench, that's a mis...
by Tommy Atkins
Tue May 15, 2018 6:06 pm
Forum: Reloading
Topic: Advice on annealing--and YouTube posts to evaluate
Replies: 18
Views: 288
Canada

Re: Advice on annealing--and YouTube posts to evaluate

Now you simply repeat the load~rotate~insert round~drop sequence for all your other shells in that batch!
You can see he discoloration from the annealing in this short test run.
by Tommy Atkins
Tue May 15, 2018 6:03 pm
Forum: Reloading
Topic: Advice on annealing--and YouTube posts to evaluate
Replies: 18
Views: 288
Canada

Re: Advice on annealing--and YouTube posts to evaluate

DSCF0525.JPG Start the rotation first, then slide the case neck & mouth into the flame, you want it a little past the tip of the blue flame. Watch the orange dab, while timing the seconds. (I just count 1 hippopotamus, 2 hippopotamus . . . ) As soon as the orange turns black immediately remove the ...
by Tommy Atkins
Tue May 15, 2018 5:58 pm
Forum: Reloading
Topic: Advice on annealing--and YouTube posts to evaluate
Replies: 18
Views: 288
Canada

Re: Advice on annealing--and YouTube posts to evaluate

To use simply put about 1/2 a bowl of tap water in the bowl. (more on that later). Light the torch & back the flame off to the smallest you can get with the "electric blue" cone in it. Clamp the "shell holder" in your power screwdriver or electric drill as long as you can keep the speed down. I have...
by Tommy Atkins
Tue May 15, 2018 5:51 pm
Forum: Reloading
Topic: Advice on annealing--and YouTube posts to evaluate
Replies: 18
Views: 288
Canada

Re: Advice on annealing--and YouTube posts to evaluate

Thew "shell holder is a deep well socket of the right size to drop the case into, but let it fall out when you tip it up. The 2 "crayons" are THE SINGLE MOST IMPORTANT PART OF THE PROCESS a way of actually measuring the temperature of the heated area. you need between 500 ~ 600 degrees to properly t...
by Tommy Atkins
Tue May 15, 2018 5:49 pm
Forum: Reloading
Topic: Advice on annealing--and YouTube posts to evaluate
Replies: 18
Views: 288
Canada

Re: Advice on annealing--and YouTube posts to evaluate

You're absolutely right about there being a lot of conflicting (& wrong) information out there. Let me do some brush clearing with illustrations for you. You need to apply heat to the neck & shoulder area ONLY. You need to apply it evenly round the whole cylindrical form. It needs to be controlled h...
by Tommy Atkins
Thu May 10, 2018 12:23 pm
Forum: Second Amendment Front
Topic: Dicks Sporting Goods Hires Anti Gun Lobbyists
Replies: 6
Views: 433
Canada

Re: Dicks Sporting Goods Hires Anti Gun Lobbyists

Yup, they're getting some solid push back now.
Mossburg dumps dicks.jpg
by Tommy Atkins
Thu May 10, 2018 9:28 am
Forum: Bayonets, Knives and Swords
Topic: Pat '07 Bayonet for my SMLE
Replies: 6
Views: 175
Canada

Re: Pat '07 Bayonet for my SMLE

Someone pointed out its not a Broad Arrow, but a badly struck "X" a bending test proof.
by Tommy Atkins
Wed May 09, 2018 12:19 pm
Forum: Bayonets, Knives and Swords
Topic: Pat '07 Bayonet for my SMLE
Replies: 6
Views: 175
Canada

Re: Pat '07 Bayonet for my SMLE

last
Pat 07 bayo 4.jpg

Go to advanced search